有份專業術語不懂!還請高手們幫幫忙!HON-KWANG ELECTRIC CO LTD SPECIFICATION MODEL NO HKP-03555 DESIGNED NO 03555-1002
COPE TYPE:EI-28
1,SURFACE:Damage,rusting,foam not pormitted.
2,STRAIN RELIEF TEST: 3LBS for 10 seconds in any direction.
電子專業術語還請幫忙
全部回復(14)
正序查看
倒序查看
@fhchuanqi
型號:EI-281.表面:損壞、生銹、起泡不能通過(就是表面有這些現象就算不合格)2.承受壓力測試:任意方向施加3英磅的力,持續10秒以上僅供參考.
謝謝你!還有一些:請幫忙:
3.CHARACTERISTICS:
3.1 :PRIMARY RATED VOLTAGE&LINE FREQUENCY:230V50Hz
3.1.1:PRIMARY EXCFTING CURRENT(lo)230V50Hz,40mA MAX
3.2:SECONDARY OUTPUT VOLTAGE:
1846291183532604.doc
3.CHARACTERISTICS:
3.1 :PRIMARY RATED VOLTAGE&LINE FREQUENCY:230V50Hz
3.1.1:PRIMARY EXCFTING CURRENT(lo)230V50Hz,40mA MAX
3.2:SECONDARY OUTPUT VOLTAGE:
1846291183532604.doc
0
回復
@fhchuanqi
性能:1.初級電壓和頻率2.初級空載電流3.次級輸出電壓看來你不是搞電子的.你找一份中文的變壓器規格書看看吧1595941183541859.doc
真的很謝謝你們,考慮到時間的關系我做錯了各位,請原諒!現在我把其它的發過來.還請幫忙!
3.3: HI-POT TEST:Shall witnstand without breakdown (1)3.75Kv50/60Hz for one minute between primary to secondary&core.(2)1Kv50/60Hz for one minute between secondary to core .At an alternative potentials 20%highermay be applied for one second (sensitivity current 1mA)
3.4:INDUCED VOLTAGE TEST:All secondary windings open lnput primary 450V 400Hz for 15 seconds shall withstand without breakdown .
3.5:INSULATION TEST:500VDC100megaohm min ,primary winding winding to secondary windings and core .
3.6:TEMPERATURE RISE :75℃max (at 25℃)with load shown on the test circuit .
3.7:HUMIDITY TEST:After 6hours in 402℃ambrent temperature at 90-95%RH shall withstand.
3.8:STORAGE TEMPERATURE:-5~60℃
3.9:OPERATION TEMPERATURE:-5~40℃
4:THIS SPECIFICATION SUBJECT TO
5: TEST CIRCUIT DIAGRAM
6:APPENDIX:Overall drawing ,illustration and material list .
3.3: HI-POT TEST:Shall witnstand without breakdown (1)3.75Kv50/60Hz for one minute between primary to secondary&core.(2)1Kv50/60Hz for one minute between secondary to core .At an alternative potentials 20%highermay be applied for one second (sensitivity current 1mA)
3.4:INDUCED VOLTAGE TEST:All secondary windings open lnput primary 450V 400Hz for 15 seconds shall withstand without breakdown .
3.5:INSULATION TEST:500VDC100megaohm min ,primary winding winding to secondary windings and core .
3.6:TEMPERATURE RISE :75℃max (at 25℃)with load shown on the test circuit .
3.7:HUMIDITY TEST:After 6hours in 402℃ambrent temperature at 90-95%RH shall withstand.
3.8:STORAGE TEMPERATURE:-5~60℃
3.9:OPERATION TEMPERATURE:-5~40℃
4:THIS SPECIFICATION SUBJECT TO
5: TEST CIRCUIT DIAGRAM
6:APPENDIX:Overall drawing ,illustration and material list .
0
回復
@愛電的痞子
真的很謝謝你們,考慮到時間的關系我做錯了各位,請原諒!現在我把其它的發過來.還請幫忙!3.3:HI-POTTEST:Shallwitnstandwithoutbreakdown(1)3.75Kv50/60Hzforoneminutebetweenprimarytosecondary&core.(2)1Kv50/60Hzforoneminutebetweensecondarytocore.Atanalternativepotentials20%highermaybeappliedforonesecond(sensitivitycurrent1mA)3.4:INDUCEDVOLTAGETEST:Allsecondarywindingsopenlnputprimary450V400Hzfor15secondsshallwithstandwithoutbreakdown.3.5:INSULATIONTEST:500VDC100megaohmmin,primarywindingwindingtosecondarywindingsandcore.3.6:TEMPERATURERISE:75℃max(at25℃)withloadshownonthetestcircuit.3.7:HUMIDITYTEST:After6hoursin402℃ambrenttemperatureat90-95%RHshallwithstand.3.8:STORAGETEMPERATURE:-5~60℃3.9:OPERATIONTEMPERATURE:-5~40℃4:THISSPECIFICATIONSUBJECTTO5:TESTCIRCUITDIAGRAM6:APPENDIX:Overalldrawing,illustrationandmateriallist.
呵呵,有意思
0
回復
