(很急!)各位高手們,請教,燈具的slope(tilt) test
各位高手,在我的映像中好象只有rough service portable floor or table luminaires 才需做slope(tilt) test,對于general purpose portable floor or table luminiares不需要做此測試,但我手頭上沒有60598-2-4關與general purpose portable luminiares 的標準,所以不敢確定,請各為高手表決一下您們的高見,謝謝!如果哪位大哥能上傳一個60598-2-4和outdoor use 的太陽能燈(節能燈)的標準,不勝感激!
全部回復(6)
正序查看
倒序查看
@alvis.tan
謝謝!大哥,你有沒有EN60598-2-4,幫忙上傳一個怎么樣?
SORRY, I have not this standard.
but almsot the same with IEC 60598-1,
just another one important point you can remember:
the flex size at least 0.75mm2 but if the product is less than 1 kg and its current not exceed 2.5A, its flex length less than 2M can used 0.5mm2 size.
but almsot the same with IEC 60598-1,
just another one important point you can remember:
the flex size at least 0.75mm2 but if the product is less than 1 kg and its current not exceed 2.5A, its flex length less than 2M can used 0.5mm2 size.
0
回復
@superjohnyao
SORRY,Ihavenotthisstandard.butalmsotthesamewithIEC60598-1,justanotheroneimportantpointyoucanremember:theflexsizeatleast0.75mm2butiftheproductislessthan1kganditscurrentnotexceed2.5A,itsflexlengthlessthan2Mcanused0.5mm2size.
fist all, thank you very much!
I have read EN60598-1,I didn't find the slope(tilt) test requirements for general purpose portable floor or table luminiares,only the requirement for rough service luminiares was found in 60598-1. so what would you think of it? I respectly beg you response me, it is emergent. thanks!
I have read EN60598-1,I didn't find the slope(tilt) test requirements for general purpose portable floor or table luminiares,only the requirement for rough service luminiares was found in 60598-1. so what would you think of it? I respectly beg you response me, it is emergent. thanks!
0
回復
@alvis.tan
fistall,thankyouverymuch!IhavereadEN60598-1,Ididn'tfindtheslope(tilt)testrequirementsforgeneralpurposeportablefloorortableluminiares,onlytherequirementforroughserviceluminiareswasfoundin60598-1.sowhatwouldyouthinkofit?Irespectlybegyouresponseme,itisemergent.thanks!
It should be passed by 6 degree test at product its severe condition( it means the product should be assembled all parts together and at its severe condtion as possible as product can).
this requirement is not so strickt,as we always pass it at 10 degree or 15 degree slope test.
you know household products mostly be required pass by 15 degree( IEC 60335-1)
Hope this make sense to you.
this requirement is not so strickt,as we always pass it at 10 degree or 15 degree slope test.
you know household products mostly be required pass by 15 degree( IEC 60335-1)
Hope this make sense to you.
0
回復